![]() The symbol indicates that this product and/or battery should not be disposed of with household waste. Rowkin hereby declares that this wireless device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive.Īny changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipmentĭo not expose this product to liquid or excessive heat. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this deice must accept any interference received, including interference that may cause undesired operation. This device complies with Part 15 of the FCC rules and industry Canada license-exempt RSS standards. To prevent possible hearing damage, do not listen at high volume levels for long periods. The louder it is, the less time you can be exposed to it. Monitor your use hearing loss is function of loudness versus time. Noise levels are measured in decibels (dB) exposure to any noise at or above 85 dB can cause gradual hearing loss. After placing the earphones in your ear, gradually turn up the volume until you reach a comfortable listening level. To avoid hearing damage, make sure that the volume on your music player is turned down before connecting your earphones. Please avoid wearing our earphones while driving. It is dangerous to drive while wearing the earphones and in many places illegal because it decreases your changes of hearing life-saving sounds outside of your vehicle, such as another car’s horn and emergency vehicle sirens. The ascent double charge full#SAFETY INFORMATION / STATEMENTSĭo not use earphones when it is unsafe to do so: while operating a vehicle, crossing the street, or during any activity or in an environment where your full attention to your surroundings is required. The human body may interfere and weaken signal in some conditions. The ascent double charge Bluetooth#TROUBLESHOOTINGįor the best Bluetooth connection, keep source device in direct view of the earbuds. Follow the initial setup instructions to reconnect the earbuds to your device.ĭo not place earbuds logo-side down on a surface, as this can wear down touch capabilities.Hold until earbud light blinks white twice.Press and hold touch surface of either earbud.Place both earbuds into the charging case and make sure they are charging.If you experience any malfunction with the earbuds, follow these instructions to reset your device. Place earbuds back in the case or press and hold the button until you hear “Power O” (approx. Take earbuds out of the case orpress and hold the earbud surface until you hear “Power On” (approx. Once the LED stops flashing red and white on the Right earbud, you are connected and ready to experience true wireless sound.Go to Bluetooth settings on your device and select “Rowkin Ascent”.Once the earbuds are synced to each other, the Right earbud will flash red and white to indicate it has entered pairing mode.A red LED light will be lit followed by blinking white LED lights, (takes approximately 5 seconds.).You will hear “Power On” from both earbuds. Earbuds turn on automatically when they are removed from the case.Be sure to place them so the LED lights are visible. Remove earbuds from case and place next to each other on a flat surface.These earbuds will automatically sync to each other. Refer to diagram below.ĭo not place other objects on Qi charging pad. Charge pad LED light will slowly blink as device charges.įor optimal performance, your device should be placed in the proper location on the pad. ![]() ![]() To charge the Ascent charging case, place charging case directly on top of Qi wireless charging pad. To use the Qi charger, plug the charging pad into a power source using the included USB cable. The 5W single coil Qi charger charges your Rowkin Ascent products and other Qi-compatible devices. (Included with purchase of Ascent Charge+) ![]() Lightly shake charging case to check battery levels. Simply plug the USB-C cable into the port on the bottom of the case and then connect the other end to your device. The charging case also acts as a power bank for your other devices. Plug the USB-C cable into the port on the bottom of the case and then connect to power. ![]() To charge the charging case, place charging case directly on top of Qi wireless charger Once they are fully charged, the LED will turn. When earbuds are charging, the red LED will blink. To charge your earbuds place both earbuds in the charging case. ROWKIN APPĭownload the Rowkin Mobile App on your phone to access “Find My Earbuds” feature and sound customization. The 5W single coil Qi charger allows you to charge your Ascent Charge and other compatible mobile devices. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |